- Description
- Features
- Specification
- Care and Safety
Highchair tray sticker for suction plates/bowls
Do you have a highchair and none of your well-invested tableware with suction will stick on to the tray? Are you struggling to get them to continue sticking on to the tray? Air finding its way in and gradually releasing the hold?
This can be a common problem and it's not much of a secret anymore. But for those who didn't know, some highchair trays, like the Stokke Tripp Trapp, have a textured and porous finish that makes suction bowls/plates impossible to stick on to. This is obviously nothing you can see with the naked eye, but for us with experience, we know this is a common issue and we're here to help you out! We know the struggle!
With our easy-to-apply, long-lasting transparent sticker, it transforms your textured tray surface into a smooth one so you can properly use your tableware with suction. Our sticker is the best all-round solution for you, so look no further! Now you can say goodbye to unwanted spills and upset dinners!
Please note that this sticker is a one-time application product. Once it is removed, it cannot be used again.
For optimal results, make sure to follow our application instructions below or watch our provided video attached.
- Clean the tray/table surface using a soft sponge with soap and water. Make sure you rinse the tray/table surface thoroughly with water until there is no soap or residue remaining.
- Once the surface is dry, we kindly ask you to wipe the surface with the provided alcohol wipe to really make sure the last traces of grease and dirt are gone.
- Pour water (about half a cup) on the surface and place the sticker on the tray, over the water. The water will allow you to adjust and reposition the sticker. You can lift the sticker and move it around until you find the perfect placement. Ensure you're not placing the sticker too close to the curves of the tray. It should be placed on the flat area of the tray. If you don't place it on the flat area, then it may cause bubble/gap at the edge of the sticker which is no good ☹.
- Once the sticker is properly positioned, remove any excess water with a cloth. Now you want to remove any air/water bubbles from under the sticker. You want to make sure it is completely flat by stroking the surface, from the center and working your way outwards using your fingers first.
- Remove wrinkles or air bubbles with a squeegee. It´s now important to really flatten the sticker out so all the bubbles come out, even the last drop. Use the provided squeegee or plastic card wrapped in a soft cloth or (ideally a microfiber cloth) and once again work your way from the center and out towards the edges to smooth out any remaining air or water bubbles. Then take a dry cloth and once again press down the edges of the sticker and remove any remaining water.
The trick is to make sure you push out as much water as possible. This procedure can be repeated until there is not a drop of water coming out from underneath the sticker's edge. Press really well, but please grab the tray underneath so you don't break it.
- To seal the sticker well, use a hair dryer with the low temperature to warm the sticker (a few minutes). The heat softens the sticker, which can help it adhere more easily. But this step is optional.
- Do step 5 again, that is using the plastic card wrapped in a soft cloth and dragging it from the center to the edges to get out the last drop of excess water from under the sticker.
- Using the suction cup right away could weaken the seal. Avoid putting anything or applying pressure to the sticker right after you put it up. Give the sticker a chance to set so it holds firm. Let the sticker settle for a minimum of 10 hours before use, but ideally 24 hours.
-
Now your tray is ready for some action!
Product Safety
Free of BPA, PVC, phthalates, lead, cadmium and other hormone-disrupting chemicals.
Swedish Design
When you buy our high-quality silicone products, you can be confident that they will stand the test of time and the cost per use will justify the investment. They will not warp, break, crack or get chipped compared to other materials, giving silicone products a long lifespan and making them more sustainable. This durability together with our idea of gender-neutral colors makes our tableware perfect for handing down to your next child or to the next generation or for upcycling.
Upcycling
When properly cared for, your Atelier Keen products will last for years but they're also great to upcycle! By prolonging the lifetime and usage of each product, you'll lower its environmental impact significantly. It´s always better to keep them in use and give them a second life! Here's an idea! How about stocking your toddler's play kitchen with a set of outgrown tableware for their imaginative play. They can pretend to have a coffee shop and have tea parties serving they're very important guests (stuffed animals). Remember, they're even dishwasher safe, in case your kid happens to eat a real snack off them, too.